Abrasion resistance is an important performance requirement in warehouse and industrial floors. Floors can be exposed to quite aggressive actions from trucks and other equipment.
Tests are carried out using our purpose designed and built equipment which conforms to the requirements of BS EN 13892-4: 2002. Known as the BCA abrasion test machine, the floor surface is assessed by measuring the depth of wear created by three hardened wheels rotating over a circular (template marked) area for a standard number of revolutions (2850 + / – 10).
The depth of wear is used to assess the quality of the floor and classifies it in accordance with BS 8204-2:2003+A2:2011. Each test is accompanied by a Face Consultants report. Where the classification is lower than required, Face can investigate and advise on the significance of the results, and on any remediation steps that should be taken.
Abrasion Testing, or any other topic related to floors can be provided as part of FACE Expert Witness Services.
Table 3 – Classification of abrasion resistance and limiting depths of wear for the abrasion test: Recommendations for concrete bases, directly finished (DF) only, as wearing surfaces
|Class||Service Conditions||Application||Maximum test wear depth mm||Typical examples (see 6.2)|
|Type of concrete||Minimum compressive strength class a N/mm2||Minimum cement content kg/m3||Type of coarse aggregate||Type of fine aggregate||Finishing process|
|AR0.5 (special)/DF||Severe abrasion and impact from steel or hard plastics wheeled traffic or scoring by dragged metal objects||Very heavy duty engineering workshops and very intensively used warehouses, etc.||0.05||Specially designed proprietary concretes||Special concretes which are not classified by strength class or minimum cement content and might contain aggregates that do not conform to 5.3. Special finishing techniques may be used. The suitability of concrete flooring for this class should be established with the manufacturer or flooring contractor offering warranty|
|AR1/DF||Very high abrasion; steel or hard plastics wheeled traffic and impact||Heavy duty industrial workshops, intensively used warehouses, etc.||0.1|
|AR2/DF||High abrasion; steel or hard plastics wheeled traffic||Medium duty industrial and commercial||0.2||Direct finished concrete||C40/50 RC50||400||Aggregates conforming to 5.3.2||Fine aggregate conforming to 5.3.3||Power floating and repeated power troweling as 10.7|
|AR4/DF||Moderate abrasion: rubber-tyred traffic||Light duty industrial and commercial||0.4||Direct finished concrete||C32/40 RC40||325|
|* Concrete should conform to BS 8500-2.|
Table 4 – Classification of abrasion resistance and limiting depths of wear for the abrasion test: Recommendations for concrete bases upgraded by dry shake/sprinkle finishes and for applied wearing screeds (WS)
|Class||Services Conditions||Application||Maximum test wear depth mm||Type of wearing screed material||Notes|
|AR0.5 (special)/WS||Severe abrasion and impact from steel or hard plastics wheeled traffic or scoring by dragged metal objects||Very heavy duty engineering workshops and very intensively used warehouses, etc.||0.05||Proprietary dry shake/sprinkle finishes on concrete grade at least as for AR3/DF||Proprietary dry shake/sprinkle finishes, which are not classified by strength class or minimum cement content and might contain aggregates that do not conform to 5.3. Special finishing techniques may be used. The suitability of concrete flooring for this class should be established with the manufacturer or flooring contractor offering warranty.|
|AR1/WS||Very high abrasion; steel or hard plastics wheeled traffic and impact||Heavy duty industrial workshops, intensively used warehouses, etc.||0.1||Monolithic or bonded wearing screed||
For wearing screed materials see 9.2.
Approved aggregates conforming to 5.3.4
Fine aggregate conforming to 5.3.5.
Hand trowelling or power floating and repeated power trowelling as 10.7
|AR2/WS||High abrasion; steel or hard plastics wheeled traffic||Medium duty industrial and commercial||0.2|
|AR4/WS||Moderate abrasion: rubber-tyred traffic||Light duty industrial and commercial||0.4|
Note: As well as the tables above, The Concrete Society’s Technical Report No 34 4th edition (Current) states that 1 test per 4000m2 is adequate, and that the minimum required abrasion resistance should be 0.20mm. This equates to a minimum requirement of AR2.
It is also worth noting that prior to TR34 4th Edition quoted above, no official document has ever given any guidance on a sampling rate.
See our testing services in action
A floors ability to resist abrasion is a very important factor. To carry out an abrasion test, eight test locations are marked on the floor using a machined template. Readings are then taken at each of the eight test locations using a digital depth gauge.
Face consultants are able to carry out tests on samples either at your site or in our Laboratory, as well as testing the floor in situ.
Concrete slab abrasion resistance tests can be conducted using the Abrasion Resistance Testing Machine to carry out tests in accordance with EN 13892-4
Face Consultants is a provider of surface abrasion testing services either at your site or in our laboratory.
Please contact us if you have any questions about our floor testing or design & consultancy services.
"We have used Face Consultants Ltd for a number of..."
Project Manager Sir Robert McAlpine Ltd
"Thank you for the results, which certainly make for interesting..."
Senior ManagerLeading Manufacturer (Leisure Industry)
"Just a note to thank you and your colleagues for..."
Project Manager McElroy Associates